1. SPECIFICATIONS
Model PURY-P300YLM-A1 (-BS)
Number of HBC controller Single HBC Double HBC
Power source 3-phase 4-wire 380-400-415 V 50/60 Hz
Cooling capacity *1 kW 33.5
(Nominal) kcal/h 28,800
*1 BTU/h 114,300
Power input kW 13.34 11.31
Current input A 22.5-21.3-20.6 19.0-18.1-17.4
EER kW/kW 2.51 2.96
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F)
cooling *3 Outdoor D.B. -5.0~46.0°C (23~115°F)
Heating capacity *2 kW 37.5
(Nominal) kcal/h 32,300
*2 BTU/h 128,000
Power input kW 12.71 11.94
Current input A 21.4-20.3-19.6 20.1-19.1-18.4
COP kW/kW 2.95 3.14
Temp. range of Indoor D.B. 15.0~27.0°C (59~81°F)
heating *3 Outdoor W.B. -20.0~15.5°C (-4~60°F)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity WP15~WP50/3~30
Sound pressure level (measured in anechoic room) dB <A> 62.5
Sound power level (measured in anechoic room) dB <A> 86
Refrigerant High pressure mm (in.) 19.05 (3/4) Brazed
piping diameter Low pressure mm (in.) 22.2 (7/8) Brazed
FAN Type x Quantity Propeller fan x 1
Air flow rate m3/min 230
L/s 3,833
cfm 8,121
Control, Driving mechanism Inverter-control, Direct-driven by motor
Motor output kW 0.92 x 1
*4 External static press. 0 Pa (0 mmH2O)
Compressor Type Inverter scroll hermetic compressor
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 8.1
Case heater kW -
Lubricant MEL32
External finish Pre-coated galvanized steel sheets (+powder coating for -BS type)
<MUNSELL 5Y 8/1 or similar>
External dimension H x W x D mm 1,710 (1,650 without legs) x 1,220 x 740
in. 67-3/8 (65 without legs) x 48-1/16 x 29-3/16
Protection devices High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Compressor -
Fan motor -
Refrigerant Type x original charge R410A x 10.3 kg (23 lbs)
Control HBC controller
Net weight kg (lbs) 248 (547)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle, Hot gas)
Drawing External WKJ94T177
Wiring WKE94G041
Standard attachment Document Installation Manual
Accessory Refrigerant conn. pipe
Optional parts Main HBC controller: CMB-WP108, 1016V-GA1
Sub HBC controller: CMB-WP108, 1016V-GB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
Notes: Unit converter
1.Nominal cooling conditions (subject to JIS B8615-2)
Indoor: 27°CD.B./19°CW.B. (81°FD.B./66°FW.B.), Outdoor: 35°CD.B. (95°FD.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
2.Nominal heating conditions (subject to JIS B8615-2)
Indoor: 20°CD.B. (68°FD.B.), Outdoor: 7°CD.B./6°CW.B. (45°FD.B./43°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
3.-5°CD.B. (23°FD.B.)/-6°CW.B. (21°FW.B.) to 21°CD.B. (70°FD.B.)/15.5°CW.B. (60°FW.B.) with cooling/heating mixed operation.
4.External static pressure option is available (30 Pa, 60 Pa/3.1 mmH2O, 6.1 mmH2O).
BTU/h =kW x 3,412 cfm =m3/min x 35.31 lbs =kg/0.4536 *Above specification data is subject to rounding variation.
0000003554.BOOK 5 ページ ２０１５年９月１４日 月曜日 午前１０時２１分
OUTDO O R
1. SPECIFICATIONS
Model PURY-P350YLM-A1 (-BS)
Number of HBC controller Single HBC Double HBC
Power source 3-phase 4-wire 380-400-415 V 50/60 Hz
Cooling capacity *1 kW 40.0
(Nominal) kcal/h 34,400
*1 BTU/h 136,500
Power input kW 17.93 14.59
Current input A 30.2-28.7-27.7 24.6-23.3-22.5
EER kW/kW 2.23 2.74
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F)
cooling *3 Outdoor D.B. -5.0~46.0°C (23~115°F)
Heating capacity *2 kW 45.0
(Nominal) kcal/h 38,700
*2 BTU/h 153,500
Power input kW 15.51 14.35
Current input A 26.1-24.8-23.9 24.2-23.0-22.1
COP kW/kW 2.90 3.13
Temp. range of Indoor D.B. 15.0~27.0°C (59~81°F)
heating *3 Outdoor W.B. -20.0~15.5°C (-4~60°F)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity WP15~WP50/4~35
Sound pressure level (measured in anechoic room) dB <A> 62.5
Sound power level (measured in anechoic room) dB <A> 86
Refrigerant High pressure mm (in.) 19.05 (3/4) Brazed
piping diameter Low pressure mm (in.) 28.58 (1-1/8) Brazed
FAN Type x Quantity Propeller fan x 1
Air flow rate m3/min 230
L/s 3,833
cfm 8,121
Control, Driving mechanism Inverter-control, Direct-driven by motor
Motor output kW 0.92 x 1
*4 External static press. 0 Pa (0 mmH2O)
Compressor Type Inverter scroll hermetic compressor
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 10.5
Case heater kW -
Lubricant MEL32
External finish Pre-coated galvanized steel sheets (+powder coating for -BS type)
<MUNSELL 5Y 8/1 or similar>
External dimension H x W x D mm 1,710 (1,650 without legs) x 1,220 x 740
in. 67-3/8 (65 without legs) x 48-1/16 x 29-3/16
Protection devices High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Compressor -
Fan motor -
Refrigerant Type x original charge R410A x 10.3 kg (23 lbs)
Control HBC controller
Net weight kg (lbs) 248 (547)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle, Hot gas)
Drawing External WKJ94T177
Wiring WKE94G041
Standard attachment Document Installation Manual
Accessory Refrigerant conn. pipe
Optional parts Main HBC controller: CMB-WP108, 1016V-GA1
Sub HBC controller: CMB-WP108, 1016V-GB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
Notes: Unit converter
1.Nominal cooling conditions (subject to JIS B8615-2)
Indoor: 27°CD.B./19°CW.B. (81°FD.B./66°FW.B.), Outdoor: 35°CD.B. (95°FD.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
2.Nominal heating conditions (subject to JIS B8615-2)
Indoor: 20°CD.B. (68°FD.B.), Outdoor: 7°CD.B./6°CW.B. (45°FD.B./43°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
3.-5°CD.B. (23°FD.B.)/-6°CW.B. (21°FW.B.) to 21°CD.B. (70°FD.B.)/15.5°CW.B. (60°FW.B.) with cooling/heating mixed operation.
4.External static pressure option is available (30 Pa, 60 Pa/3.1 mmH2O, 6.1 mmH2O).
BTU/h =kW x 3,412 cfm =m3/min x 35.31 lbs =kg/0.4536 *Above specification data is subject to rounding variation.
0000003554.BOOK 6 ページ ２０１５年９月１４日 月曜日 午前１０時２１分
OUT D OOR
1. SPECIFICATIONS
Model PURY-P400YLM-A1 (-BS) PURY-P450YLM-A1 (-BS)
Power source 3-phase 4-wire 380-400-415 V 50/60 Hz 3-phase 4-wire 380-400-415 V 50/60 Hz
Cooling capacity *1 kW 45.0 50.0
(Nominal) kcal/h 40,000 45,000
*1 BTU/h 153,500 170,600
Power input kW 16.65 17.92
Current input A 28.1-26.7-25.7 30.2-28.7-27.7
EER kW/kW 2.70 2.79
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F) 15.0~24.0°C (59~75°F)
cooling *3 Outdoor D.B. -5.0~46.0°C (23~115°F) -5.0~46.0°C (23~115°F)
Heating capacity *2 kW 45.0 56.0
(Nominal) kcal/h 40,000 50,000
*2 BTU/h 153,500 191,100
Power input kW 13.39 17.39
Current input A 22.6-21.4-20.6 29.3-27.8-26.8
COP kW/kW 3.36 3.22
Temp. range of Indoor D.B. 15.0~27.0°C (59~81°F) 15.0~27.0°C (59~81°F)
heating *3 Outdoor W.B. -20.0~15.5°C (-4~60°F) -20.0~15.5°C (-4~60°F)
Indoor unit Total capacity 50~150% of outdoor unit capacity 50~150% of outdoor unit capacity
connectable Model/Quantity WP15~WP50/4~40 WP15~WP50/5~45
Sound pressure level (measured in anechoic room) dB <A> 62.5 62.5
Sound power level (measured in anechoic room) dB <A> 86 86
Refrigerant High pressure mm (in.) 22.2 (7/8) Brazed 22.2 (7/8) Brazed
piping diameter Low pressure mm (in.) 28.58 (1-1/8) Brazed 28.58 (1-1/8) Brazed
FAN Type x Quantity Propeller fan x 1 Propeller fan x 2
Air flow rate m3/min 230 320
L/s 3,833 5,333
cfm 8,121 11,299
Control, Driving mechanism Inverter-control, Direct-driven by motor Inverter-control, Direct-driven by motor
Motor output kW 0.92 x 1 0.92 x 2
*4 External static press. 0 Pa (0 mmH2O) 0 Pa (0 mmH2O)
Compressor Type Inverter scroll hermetic compressor Inverter scroll hermetic compressor
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter Inverter
Motor output kW 10.9 12.4
Case heater kW - -
Lubricant MEL32 MEL32
External finish Pre-coated galvanized steel sheets (+powder coating for -BS
type) Pre-coated galvanized steel sheets (+powder coating for -BS type)
<MUNSELL 5Y 8/1 or similar> <MUNSELL 5Y 8/1 or similar>
External dimension H x W x D mm 1,710 (1,650 without legs) x 1,220 x 740 1,710 (1,650 without legs) x 1,750 x 740 in. 67-3/8 (65 without legs) x 48-1/16 x 29-3/16 67-3/8 (65 without legs) x 68-15/16 x 29-3/16 Protection devices High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Compressor - -
Fan motor - -
Refrigerant Type x original charge R410A x 10.3 kg (23 lbs) R410A x 11.8 kg (27 lbs)
Control HBC controller HBC controller
Net weight kg (lbs) 246 (543) 321 (708)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) - -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle, Hot gas) Auto-defrost mode (Reversed refrigerant cycle, Hot gas)
Drawing External WKJ94T177 WKJ94T178
Wiring WKE94G041 WKE94G042
Standard attachment Document Installation Manual Installation Manual
Accessory Refrigerant conn. pipe Refrigerant conn. pipe
Optional parts
Main HBC controller: CMB-WP108,1016V-GA1 Main HBC controller: CMB-WP108,1016V-GA1 Sub HBC controller: CMB-WP108,1016V-GB1 Sub HBC controller: CMB-WP108,1016V-GB1
Remarks Details on foundation work, duct work, insulation work, electri-
cal wiring, power source switch, and other items shall be re- ferred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
Details on foundation work, duct work, insulation work, electri- cal wiring, power source switch, and other items shall be re- ferred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
Notes: Unit converter
1.Nominal cooling conditions (subject to JIS B8615-2)
Indoor: 27°CD.B./19°CW.B. (81°FD.B./66°FW.B.), Outdoor: 35°CD.B./24°CW.B. (95°FD.B./75°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
2.Nominal heating conditions (subject to JIS B8615-2)
Indoor: 20°CD.B. (68°FD.B.), Outdoor: 7°CD.B./6°CW.B. (45°FD.B./43°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
3.-5°CD.B. (23°FD.B.)/-6°CW.B. (21°FW.B.) to 21°CD.B. (70°FD.B.)/15.5°CW.B. (60°FW.B.) with cooling/heating mixed operation.
BTU/h =kW x 3,412 cfm =m3/min x 35.31 lbs =kg/0.4536
*Above specification data is 0000003554.BOOK 7 ページ ２０１５年９月１４日 月曜日 午前１０時２１分
OUTDO O R
1. SPECIFICATIONS
Model PURY-P500YLM-A1 (-BS)
Power source 3-phase 4-wire 380-400-415 V 50/60 Hz
Cooling capacity *1 kW 56.0
(Nominal) kcal/h 50,000
*1 BTU/h 191,100
Power input kW 22.67
Current input A 38.2-36.3-35.0
EER kW/kW 2.47
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F)
cooling *3 Outdoor D.B. -5.0~46.0°C (23~115°F)
Heating capacity *2 kW 58.0
(Nominal) kcal/h 50,000
*2 BTU/h 197,900
Power input kW 17.53
Current input A 29.5-28.1-27.0
COP kW/kW 3.30
Temp. range of Indoor D.B. 15.0~27.0°C (59~81°F)
heating *3 Outdoor W.B. -20.0~15.5°C (-4~60°F)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity WP15~WP50/5~50
Sound pressure level (measured in anechoic room) dB <A> 63.5
Sound power level (measured in anechoic room) dB <A> 87
Refrigerant High pressure mm (in.) 22.2 (7/8) Brazed
piping diameter Low pressure mm (in.) 28.58 (1-1/8) Brazed
FAN Type x Quantity Propeller fan x 2
Air flow rate m3/min 380
L/s 6,333
cfm 13,418
Control, Driving mechanism Inverter-control, Direct-driven by motor
Motor output kW 0.92 x 2
*4 External static press. 0 Pa (0 mmH2O)
Compressor Type Inverter scroll hermetic compressor
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 13.4
Case heater kW -
Lubricant MEL32
External finish Pre-coated galvanized steel sheets (+powder coating for -BS type)
<MUNSELL 5Y 8/1 or similar>
External dimension H x W x D mm 1,710 (1,650 without legs) x 1,750 x 740
in. 67-3/8 (65 without legs) x 68-15/16 x 29-3/16
Protection devices High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Compressor -
Fan motor -
Refrigerant Type x original charge R410A x 11.8 kg (27 lbs)
Control HBC controller
Net weight kg (lbs) 321 (708)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle, Hot gas)
Drawing External WKJ94T178
Wiring WKE94G042
Standard attachment Document Installation Manual
Accessory Refrigerant conn. pipe
Optional parts
Main HBC controller: CMB-WP108,1016V-GA1 Sub HBC controller: CMB-WP108,1016V-GB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
Notes: Unit converter
1.Nominal cooling conditions (subject to JIS B8615-2)
Indoor: 27°CD.B./19°CW.B. (81°FD.B./66°FW.B.), Outdoor: 35°CD.B./24°CW.B. (95°FD.B./75°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
2.Nominal heating conditions (subject to JIS B8615-2)
Indoor: 20°CD.B. (68°FD.B.), Outdoor: 7°CD.B./6°CW.B. (45°FD.B./43°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
3.-5°CD.B. (23°FD.B.)/-6°CW.B. (21°FW.B.) to 21°CD.B. (70°FD.B.)/15.5°CW.B. (60°FW.B.) with cooling/heating mixed operation.
4.External static pressure option is available (30 Pa, 60 Pa/3.1 mmH2O, 6.1 mmH2O).
BTU/h =kW x 3,412 cfm =m3/min x 35.31 lbs =kg/0.4536
*Above specification data is subject to rounding variation.
0000003554.BOOK 8 ページ ２０１５年９月１４日 月曜日 午前１０時２１分
OUT D OOR
1. SPECIFICATIONS
Model PURY-EP200YLM-A1 (-BS) PURY-EP250YLM-A1 (-BS)
Power source 3-phase 4-wire 380-400-415 V 50/60 Hz 3-phase 4-wire 380-400-415 V 50/60 Hz
Cooling capacity *1 kW 22.4 28.0
(Nominal) kcal/h 20,000 25,000
*1 BTU/h 76,400 95,500
Power input kW 6.27 8.77
Current input A 10.5-10.0-9.6 14.8-14.0-13.5
EER kW/kW 3.57 3.19
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F) 15.0~24.0°C (59~75°F)
cooling *3 Outdoor D.B. -5.0~46.0°C (23~115°F) -5.0~46.0°C (23~115°F)
Heating capacity *2 kW 25.0 31.5
(Nominal) kcal/h 21,500 27,100
*2 BTU/h 85,300 107,500
Power input kW 6.92 9.84
Current input A 11.6-11.0-10.6 16.6-15.7-15.2
COP kW/kW 3.61 3.20
Temp. range of Indoor D.B. 15.0~27.0°C (59~81°F) 15.0~27.0°C (59~81°F)
heating *3 Outdoor W.B. -20.0~15.5°C (-4~60°F) -20.0~15.5°C (-4~60°F)
Indoor unit Total capacity 50~150% of outdoor unit capacity 50~150% of outdoor unit capacity
connectable Model/Quantity WP15~WP50/2~20 WP15~WP50/3~25
Sound pressure level (measured in anechoic room) dB <A> 59 60
Sound power level (measured in anechoic room) dB <A> 82.5 83.5
Refrigerant High pressure mm (in.) 15.88 (5/8) Brazed 19.05 (3/4) Brazed
piping diameter Low pressure mm (in.) 19.05 (3/4) Brazed 22.2 (7/8) Brazed
FAN Type x Quantity Propeller fan x 1 Propeller fan x 1
Air flow rate m3/min 185 185
L/s 3,083 3,083
cfm 6,532 6,532
Control, Driving mechanism Inverter-control, Direct-driven by motor Inverter-control, Direct-driven by motor
Motor output kW 0.92 x 1 0.92 x 1
*4 External static press. 0 Pa (0 mmH2O) 0 Pa (0 mmH2O)
Compressor Type Inverter scroll hermetic compressor Inverter scroll hermetic compressor
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter Inverter
Motor output kW 5.6 6.9
Case heater kW - -
Lubricant MEL32 MEL32
External finish Pre-coated galvanized steel sheets (+powder coating for -BS
type) Pre-coated galvanized steel sheets (+powder coating for -BS type)
<MUNSELL 5Y 8/1 or similar> <MUNSELL 5Y 8/1 or similar>
External dimension H x W x D mm 1,710 (1,650 without legs) x 920 x 740 1,710 (1,650 without legs) x 920 x 740
in. 67-3/8 (65 without legs) x 36-1/4 x 29-3/16 67-3/8 (65 without legs) x 36-1/4 x 29-3/16 Protection devices High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Compressor - -
Fan motor - -
Refrigerant Type x original charge R410A x 6.0 kg (14 lbs) R410A x 6.0 kg (14 lbs)
Control HBC controller HBC controller
Net weight kg (lbs) 202 (446) 202 (446)
Heat exchanger Salt-resistant cross fin & aluminium tube Salt-resistant cross fin & aluminium tube
HIC circuit (HIC: Heat Inter-Changer) - -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle, Hot gas) Auto-defrost mode (Reversed refrigerant cycle, Hot gas)
Drawing External WKJ94T756 WKJ94T756
Wiring WKE94G041 WKE94G041
Standard attachment Document Installation Manual Installation Manual
Accessory Refrigerant conn. pipe Refrigerant conn. pipe
Optional parts
Main HBC controller: CMB-WP108,1016V-GA1 Main HBC controller: CMB-WP108,1016V-GA1 Sub HBC controller: CMB-WP108,1016V-GB1 Sub HBC controller: CMB-WP108,1016V-GB1
Remarks Details on foundation work, duct work, insulation work, electri-
cal wiring, power source switch, and other items shall be re- ferred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
Details on foundation work, duct work, insulation work, electri- cal wiring, power source switch, and other items shall be re- ferred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
Notes: Unit converter
1.Nominal cooling conditions (subject to JIS B8615-2)
Indoor: 27°CD.B./19°CW.B. (81°FD.B./66°FW.B.), Outdoor: 35°CD.B./24°CW.B. (95°FD.B./75°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
2.Nominal heating conditions (subject to JIS B8615-2)
Indoor: 20°CD.B. (68°FD.B.), Outdoor: 7°CD.B./6°CW.B. (45°FD.B./43°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
3.-5°CD.B. (23°FD.B.)/-6°CW.B. (21°FW.B.) to 21°CD.B. (70°FD.B.)/15.5°CW.B. (60°FW.B.) with cooling/heating mixed operation.
BTU/h =kW x 3,412 cfm =m3/min x 35.31 lbs =kg/0.4536
*Above specification data is 0000003554.BOOK 9 ページ ２０１５年９月１４日 月曜日 午前１０時２１分
OUTDO O R
1. SPECIFICATIONS
Model PURY-EP300YLM-A1 (-BS)
Number of HBC controller Single HBC Double HBC
Power source 3-phase 4-wire 380-400-415 V 50/60 Hz
Cooling capacity *1 kW 33.5
(Nominal) kcal/h 28,800
*1 BTU/h 114,300
Power input kW 12.05 10.24
Current input A 20.3-19.3-18.6 17.2-16.4-15.8
EER kW/kW 2.78 3.27
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F)
cooling *3 Outdoor D.B. -5.0~46.0°C (23~115°F)
Heating capacity *2 kW 37.5
(Nominal) kcal/h 32,300
*2 BTU/h 128,000
Power input kW 11.71 11.12
Current input A 19.7-18.7-18.1 18.7-17.8-17.1
COP kW/kW 3.20 3.37
Temp. range of Indoor D.B. 15.0~27.0°C (59~81°F)
heating *3 Outdoor W.B. -20.0~15.5°C (-4~60°F)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity WP15~WP50/3~30
Sound pressure level (measured in anechoic room) dB <A> 62.5
Sound power level (measured in anechoic room) dB <A> 86
Refrigerant High pressure mm (in.) 19.05 (3/4) Brazed
piping diameter Low pressure mm (in.) 22.2 (7/8) Brazed
FAN Type x Quantity Propeller fan x 1
Air flow rate m3/min 230
L/s 3,833
cfm 8,121
Control, Driving mechanism Inverter-control, Direct-driven by motor
Motor output kW 0.92 x 1
*4 External static press. 0 Pa (0 mmH2O)
Compressor Type Inverter scroll hermetic compressor
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 8.1
Case heater kW -
Lubricant MEL32
External finish Pre-coated galvanized steel sheets (+powder coating for -BS type)
<MUNSELL 5Y 8/1 or similar>
External dimension H x W x D mm 1,710 (1,650 without legs) x 1,220 x 740
in. 67-3/8 (65 without legs) x 48-1/16 x 29-3/16
Protection devices High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Compressor -
Fan motor -
Refrigerant Type x original charge R410A x 8.0 kg (18 lbs)
Control HBC controller
Net weight kg (lbs) 244 (538)
Heat exchanger Salt-resistant cross fin & aluminium tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle, Hot gas)
Drawing External WKJ94T757
Wiring WKE94G041
Standard attachment Document Installation Manual
Accessory Refrigerant conn. pipe
Optional parts Main HBC controller: CMB-WP108, 1016V-GA1
Sub HBC controller: CMB-WP108, 1016V-GB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
Notes: Unit converter
1.Nominal cooling conditions (subject to JIS B8615-2)
Indoor: 27°CD.B./19°CW.B. (81°FD.B./66°FW.B.), Outdoor: 35°CD.B. (95°FD.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
2.Nominal heating conditions (subject to JIS B8615-2)
Indoor: 20°CD.B. (68°FD.B.), Outdoor: 7°CD.B./6°CW.B. (45°FD.B./43°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
3.-5°CD.B. (23°FD.B.)/-6°CW.B. (21°FW.B.) to 21°CD.B. (70°FD.B.)/15.5°CW.B. (60°FW.B.) with cooling/heating mixed operation.
4.External static pressure option is available (30 Pa, 60 Pa/3.1 mmH2O, 6.1 mmH2O).
BTU/h =kW x 3,412 cfm =m3/min x 35.31 lbs =kg/0.4536 *Above specification data is subject to rounding variation.
0000003554.BOOK 10 ページ ２０１５年９月１４日 月曜日 午前１０時２１分
OUT D OOR
1. SPECIFICATIONS
Model PURY-EP350YLM-A1 (-BS)
Number of HBC controller Single HBC Double HBC
Power source 3-phase 4-wire 380-400-415 V 50/60 Hz
Cooling capacity *1 kW 40.0
(Nominal) kcal/h 34,400
*1 BTU/h 136,500
Power input kW 17.16 13.98
Current input A 28.9-27.5-26.5 23.6-22.4-21.6
EER kW/kW 2.33 2.86
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F)
cooling *3 Outdoor D.B. -5.0~46.0°C (23~115°F)
Heating capacity *2 kW 45.0
(Nominal) kcal/h 38,700
*2 BTU/h 153,500
Power input kW 15.38 14.28
Current input A 25.9-24.6-23.7 24.1-22.9-22.0
COP kW/kW 2.92 3.15
Temp. range of Indoor D.B. 15.0~27.0°C (59~81°F)
heating *3 Outdoor W.B. -20.0~15.5°C (-4~60°F)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity WP15~WP50/4~35
Sound pressure level (measured in anechoic room) dB <A> 62.5
Sound power level (measured in anechoic room) dB <A> 86
Refrigerant High pressure mm (in.) 19.05 (3/4) Brazed
piping diameter Low pressure mm (in.) 28.58 (1-1/8) Brazed
FAN Type x Quantity Propeller fan x 1
Air flow rate m3/min 230
L/s 3,833
cfm 8,121
Control, Driving mechanism Inverter-control, Direct-driven by motor
Motor output kW 0.92 x 1
*4 External static press. 0 Pa (0 mmH2O)
Compressor Type Inverter scroll hermetic compressor
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 10.5
Case heater kW -
Lubricant MEL32
External finish Pre-coated galvanized steel sheets (+powder coating for -BS type)
<MUNSELL 5Y 8/1 or similar>
External dimension H x W x D mm 1,710 (1,650 without legs) x 1,220 x 740
in. 67-3/8 (65 without legs) x 48-1/16 x 29-3/16
Protection devices High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Compressor -
Fan motor -
Refrigerant Type x original charge R410A x 8.0 kg (18 lbs)
Control HBC controller
Net weight kg (lbs) 244 (538)
Heat exchanger Salt-resistant cross fin & aluminium tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External WKJ94LT757
Wiring WKE94G041
Standard attachment Document Installation Manual
Accessory Refrigerant conn. pipe
Optional parts Main HBC controller: CMB-WP108, 1016V-GA1
Sub HBC controller: CMB-WP108, 1016V-GB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
Notes: Unit converter
1.Nominal cooling conditions (subject to JIS B8615-2)
Indoor: 27°CD.B./19°CW.B. (81°FD.B./66°FW.B.), Outdoor: 35°CD.B. (95°FD.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
2.Nominal heating conditions (subject to JIS B8615-2)
Indoor: 20°CD.B. (68°FD.B.), Outdoor: 7°CD.B./6°CW.B. (45°FD.B./43°FW.B.) Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
3.-5°CD.B. (23°FD.B.)/-6°CW.B. (21°FW.B.) to 21°CD.B. (70°FD.B.)/15.5°CW.B. (60°FW.B.) with cooling/heating mixed operation.
4.External static pressure option is available (30 Pa, 60 Pa/3.1 mmH2O, 6.1 mmH2O).
BTU/h =kW x 3,412 cfm =m3/min x 35.31 lbs =kg/0.4536 *Above specification data is subject to rounding variation.
0000003554.BOOK 11 ページ ２０１５年９月１４日 月曜日 午前１０時２１分